Foamer sprayer A-Type 1.5 PRO FOAMER - EPDM

A manual foam sprayer built around a 1860 ml tank, the A-Type 1.5 PRO FOAMER works with EPDM seals for alkaline cleaning media. Usable filling volume is 1000 ml. That reserve supports longer foaming runs without frequent refills. The adjustable plastic nozzle delivers a fan jet with a 110° spray angle. Foam spreads evenly across panels, glass and floors.

Pressure is built by hand through a reinforced polypropylene pump. A safety valve vents the tank when pressure reaches 3 bar. Opening the cap also releases pressure before cleaning or servicing. The EPDM sealing set suits alkaline products with pH values from 7 to 14. The sprayer also withstands heat and chemical contact during repeated use. EPOCA manufactures the unit in Italy. Workshops, detailing studios and cleaning teams use it for snow foam work.

Manual foam sprayer A-Type 1.5 PRO FOAMER - EPDM in detail

Tank volume and working capacity

Nominal tank volume reaches 1860 ml, while the usable liquid charge is 1000 ml. The remaining headroom holds the compressed air needed for spraying. That ratio keeps foam output steady between pumping cycles. Operators can treat a full vehicle body or a large floor area before refilling. The cap opens wide for filling, rinsing and routine cleaning of the tank.

• Nominal volume: 1860 ml
• Usable capacity: 1000 ml
• Maximum working pressure: 3 bar
• Integrated pressure safety valve
• Pressure can also be released by opening the cap

Pressure management stays simple during longer jobs. When internal pressure climbs to 3 bar, the valve vents automatically. Before opening the tank for refilling, release the residual pressure first. This routine keeps handling predictable and shortens service stops in busy wash bays.

Nozzle and spray pattern

The plastic nozzle produces a fan-shaped jet with a 110° spray angle. It can be adjusted to change the jet according to the surface and the distance. The wide pattern covers large panels quickly and lays down a dense, fine foam layer. A narrower setting helps on wheel arches, sills and tight interior areas.

• Fan-effect nozzle, 110° spray angle
• Adjustable plastic nozzle head
• Produces fine, dense foam
• Even distribution over wide surfaces

Foam consistency depends on the chemical concentration and the pump charge. Keep the tank pressurised within the stated limit for a uniform jet. Rinse the nozzle with clean water after each shift. This prevents dried detergent from blocking the outlet and changing the pattern.

Seals, pump materials and chemical compatibility

EPDM seals handle alkaline cleaning agents with pH values from 7 to 14. The pump shaft is made of reinforced PP, and the pump head uses a reinforced polypropylene structure. These materials resist heat and chemical contact under repeated workshop use. Always check the detergent data sheet against the stated pH range before filling.

• Seal material: EPDM
• Compatible with alkaline media, pH 7 to 14
• Pump shaft: reinforced PP
• Pump head: reinforced polypropylene structure
• Heat and chemical resistant construction

Material choice defines the service life of any chemical sprayer. The EPDM version targets alkaline degreasers and snow foam shampoos. Acidic wheel cleaners may require a different seal specification. Drain and rinse the tank after use so residues do not attack the sealing surfaces.

Common applications

Car washing is the main task, from pre-wash foam to body degreasing. The unit also serves window cleaning, interior trim work and upholstery treatment. Detailing shops use it on wheels, sills and engine bays. Beyond vehicles, cleaning teams apply foam to floors, tables, chairs and walls. Facility maintenance crews value the 1000 ml charge for mobile work without a hose. Any alkaline detergent inside the stated pH range can be applied this way.

Catalogue technical data

The catalogue lists the A-Type 1.5 PRO FOAMER with EPDM seals as a hand-pressurised foaming sprayer made by EPOCA in Italy. Recorded values cover the 1860 ml nominal volume, the 1000 ml usable capacity, the 110° fan nozzle, the 3 bar pressure limit and the reinforced polypropylene pump assembly.