Pressure sprayer EPOCA 2000 K Professional 2 litre with brass nozzle

A 2 litre pressure sprayer with brass nozzle covers cleaning work where chemicals attack plastic parts. The EPOCA 2000 K Professional holds 2000 ml in total and 1800 ml of usable liquid. VITON seals let the unit carry acidic solutions with a pH value between 1 and 9. The adjustable brass nozzle sets the spray pattern from a fine mist to a stronger jet.

Pressure builds through a manual pump with a zinc-plated steel shaft. Working pressure reaches 3 bar, and an automatic safety valve vents the tank at that level. A locking device holds the lever in the normal position or in continuous spraying mode. The supplied 25 cm lance reaches wheel arches, engine bays and machine frames. Car washing bays, workshops and industrial cleaning teams are the usual users of this model.

Key features of the 2 litre pressure sprayer with brass nozzle

Tank, seals and chemical compatibility

The tank carries 2000 ml in total, with 1800 ml available as working volume. VITON sealing rings resist chemicals and heat, so acidic detergents stay inside without attacking the gaskets. The stated pH range runs from 1 to 9. That covers wheel cleaners, degreasers and many workshop solutions. The zinc-plated steel pump shaft withstands repeated pumping cycles during a full shift.

• Total capacity: 2000 ml
• Working capacity: 1800 ml
• Seals: VITON, resistant to chemicals and heat
• Suitable liquid pH range: 1 to 9
• Pump shaft: zinc-plated steel

Chemical compatibility is the main reason to pick this version over a standard sprayer. Acidic products often shorten the life of ordinary rubber seals. VITON keeps the seal geometry stable in that environment. Refill the tank only up to the working volume, so the air chamber still allows pumping. Rinse the tank with clean water after each chemical change to avoid residue mixing.

Pressure control, safety valve and nozzle

Maximum operating pressure is 3 bar. When the tank reaches that level, the automatic safety valve releases the excess. The lever locking device keeps the trigger open for continuous spraying, which helps on large surfaces. The brass nozzle adjusts from mist to a focused stream. Brass handles pressure better than plastic and keeps the orifice shape over long service.

• Maximum pressure: 3 bar
• Automatic safety valve venting at 3 bar
• Adjustable brass nozzle
• Lance length: 25 cm
• Lever lock for normal or continuous spraying

Check the safety valve before each session and keep the vent path clear. Do not pump beyond the point where the valve starts to release. The 25 cm lance moves the nozzle away from the hand, which suits under-body and wheel work. Loosen the nozzle to widen the cone, tighten it for a narrower jet. Store the sprayer depressurised after use.

Common applications

Car washing bays use the sprayer for pre-wash chemicals, wheel cleaners and interior products.

Detailing shops apply it for panel cleaning and trim treatment. In workshops it carries degreasers onto engine parts and machine housings. Industrial cleaning crews use it on floors, tiles and stainless surfaces. Food and beverage sites can apply sanitising solutions within the stated pH range. The 25 cm lance reaches corners, frames and shielded areas that a short nozzle cannot cover.

Catalog packing data

Two catalog references exist for the same sprayer: the labelled version and the unlabelled version. Both share identical packing figures. Each carton holds 8 sprayers and measures 39.0 x 30.0 x 46.3 cm. Carton weight is 5.28 kg with a volume of 0.054 m3. One pallet takes 38 cartons, giving 304 units. Units leave the factory in shrink-wrap film to keep dust and moisture out.

• Units per carton: 8
• Carton dimensions: 39.0 x 30.0 x 46.3 cm
• Carton weight: 5.28 kg
• Carton volume: 0.054 m3
• Cartons per pallet: 38
• Units per pallet: 304
• Packaging: shrink-wrap

Dealers and showrooms can order either the labelled or the unlabelled reference. Pallet quantities stay the same in both cases, which simplifies stock planning.