Wood carving tool set Kirschen 3441000, 11 pieces

The wood carving tool set Kirschen 3441000 brings together six carving chisels, four carving knives and one sharpening stone. All 11 pieces sit in a fitted wooden case of 245 x 245 x 45 mm. Every tool keeps its own compartment, so the edges do not rub against each other in storage. The complete set weighs 1118 g. Each piece is worked by hand at every stage of manufacture.

Chisel blades are made of HSS high-speed steel and are ground over their full length. The cutting faces are hand-polished and then covered with a thin oil film against rust. The six chisel profiles cover flat, skew, round 6 mm and 8 mm, triangular and V-groove cuts. Four knives with different blade shapes complete the range. Carvers use this combination for shaping wood and other soft materials.

What the wood carving tool set Kirschen 3441000 contains

The layout mixes chisels for volume removal with knives for detail cuts, plus a stone for re-honing at the bench. Six chisel geometries handle grooves, chamfers, hollows and V-lines. The four knives take over on fine contours and finishing passes. One two-grit stone keeps every edge in working condition without leaving the workspace.

• 6 carving chisels: flat, skew, round 6 mm, round 8 mm, triangular, V-groove
• 4 carving knives with differing blade shapes
• 1 sharpening stone, 80 x 30 x 15 mm, two grit sides
• Fitted wooden case with a separate compartment per tool
• Total weight of the set: 1118 g

Blade material and edge preparation

HSS high-speed steel forms every chisel blade, ground across the whole blade body rather than only at the bevel. The cutting edge is polished by hand, which leaves a surface ready for immediate use. A protective oil film on the blade face limits corrosion during transport and storage. The included stone offers two grit levels for shaping and finishing the edge.

• Blade material: HSS high-speed steel
• Full-length grinding on the blade
• Hand-polished cutting edges
• Anti-rust oil film on blade surfaces
• Sharpening stone with two different grit faces

Handles and wooden case

Chisel handles are turned from wood in an octagonal shape, 10 cm long and Ø19.5 mm, tapering toward the ferrule end. The flats stop the tool from rolling off the bench and give a defined grip when rotating a cut. Knife handles follow four distinct shapes and hold their blades with brass rivets. The case keeps the whole set together between jobs.

• Chisel handle: turned wood, octagonal, tapered
• Handle length: 10 cm
• Handle diameter: Ø19.5 mm
• Knife blades secured by brass rivets
• Wooden case: 245 x 245 x 45 mm, individual compartments

Common applications

Sculptors and professional carvers use the set for relief work, chip carving and figure shaping. The round chisels hollow out curved surfaces, while the V-groove and triangular profiles cut outlines and decorative lines. Flat and skew chisels clean backgrounds and level flat areas. The knives handle undercuts, small facets and finishing details. Beyond wood, the tools also shape other soft materials. Model makers, furniture restorers and craft workshops can use the same case as a portable bench kit.

Catalog reference: piece codes

Kirschen identifies each component of set 3441 by its own catalog number. The list below follows the manufacturer reference so single tools can be reordered later.

• 3201: flat chisel, straight edge, 8 mm
• 3202: 10 mm
• 3208: 6 mm and 8 mm
• 3239: 6 mm
• 3247: 2 mm
• Carving knives: 3351, 3353, 3356, 3358
• 3707: sharpening stone, 80 x 30 mm

The set is made in Germany and supplied complete in its wooden case. Because every edge is hand-polished, the tools can be put to work directly after the protective oil is wiped off. Keeping each piece in its own compartment and honing on the supplied stone maintains the geometry over long service.